Вы находитесь на странице: 1из 8

OR-JTST-0069

Request RJIL to Accept CLOT Report with Corrected KPI


KPIs

Pre-Optimization

Post-Optimization

Category

Target Value

RSRP

KPI

95%

SINR >= -2 dB

Info

93.87% (7785/8293)

99.86% (2875/2879)

99.80% (3579/3586)

Overlapping Servers within 5 dB <= 1

KPI

60%

78.00% (6468 /8292)

89.07% (2558 /2872)

PASS

87.95% (3154 /3586)

Overlapping Servers within 5 dB <= 2

KPI

90%

96.62% (8012 /8292)

99.65% (2862 /2872)

PASS

99.92% (3583 /3586)

PCI for all Sectors Observed

Info

6/6

MAC Throughput DL >= 2 Mbps

KPI

95%

93.07% (9216/9902)

99.30% (3558/3583)

MAC Throughput UL >= 256 kbps

KPI

95%

66.29% (3739/5640)

Average MAC Throughput DL (kbps)

KPI

16500

Average MAC Throughput UL (kbps)

KPI

Call Drop Rate

Non-Exclusion

Exclusion

Status

Non-Exclusion

Exclusion

Status

72.88% (6377 /8750)

96.57% (2900 /3003)

PASS

97.73% (3614 /3698)

97.75% (3480 /3560)

PASS

99.80% (3453/3460)

88.90% (3026 /3404)

PASS

99.15% (3375 /3404)

PASS

6/6

PASS

98.37% (4408/4481)

98.32% (4201/4273)

PASS

90.58% (1903/2101)

FAIL

96.01% (2524/2629)

95.94% (2413/2515)

PASS

27429.66284

37271.50975

PASS

33225.63572

33653.04529

PASS

2500

2129.368666

3418.907157

PASS

3628.212824

3645.844393

PASS

KPI

1%

0.51% (3/592.17)

0.00% (0/290.20)

PASS

0.00% (0/415.71)

0.00% (0/401.54)

PASS

TAU Success Rate

Info

81.82% (9/11)

Handover Success Rate

KPI

98%

99.78% (449/450)

100.00% (119/119)

PASS

99.33% (148/149)

99.24% (131/132)

PASS

Handover Interruption Time < 100ms

KPI

95%

99.11% (445/449)

99.16% (118/119)

PASS

100.00% (148/148)

100.00% (131/131)

PASS

RACH Success Rate

KPI

99%

93.47% (186/199)

100.00% (56/56)

FAIL

100.00% (80/80)

100.00% (76/76)

PASS

Attach Success Rate

KPI

99%

77.71% (129/166)

90.91% (50/55)

FAIL

97.50% (78/80)

98.68% (75/76)

FAIL

100.00% (78/78), PASS

VoLTE Setup Success Rate

KPI

99%

93.33% (112/120)

95.56% (43/45)

FAIL

100.00% (72/72)

100.00% (70/70)

PASS

Attach Setup Time < 1.5 s

KPI

95%

92.36% (1.02)

100.00% (0.99)

FAIL

98.73% (1.03)

98.65% (1.04)

PASS

IMS Registration Setup Time < 1.5 s

Info

95%

Report Only

2.56% (1.34)

1.33% (1.29)

Report Only

VoLTE Setup Time < 1.5 s

KPI

95%

74.11% (0.93)

95.35% (0.86)

FAIL

100.00% (1.01)

100.00% (1.01)

PASS

VoLTE Jitter < 40 ms

KPI

95%

99.99% (01.84)

100.00% (01.85)

PASS

100.00% (01.72)

100.00% (01.73)

PASS

VoLTE Latency < 100 ms

KPI

95%

VoLTE RTP Packet Loss Rate

KPI

1%

1.23%

0.07%

FAIL

0.23%

0.23%

PASS

Average BLER DL

Info

7.46

6.38

6.25

6.30

Average BLER UL

Info

11.12

8.70

8.84

8.83

2015 Samsung

Site
(Actual/Plan)

KPI Result

2/2 (100%)

16/17 17/17

Corrected KPI

Antenna Parameter Change

Modification
Changes OR-JTSG-0069

OR-JTST-0069
Analysis & Recommendation
Analysis & Suggestion
KPIs(Fail)
MAC Throughput UL
>= 256 kbps
RACH Fail

Detail Analysis
. Not Applying the PKG 4.0.0 p1

Suggestion
. Applying PKG 4.0.0 p1
. Golden Parameters

. All The RACH Failure(13 Count) Happened due


to Poor coverage area and out of BSP.

Attach Success Rate


VoLTE Setup
Success
VoLTE Setup Time
< 1.5s

. Out of BSP (Poor Signals)


. Core Issue
. Overshooting

. Modified DTR
. Change PHY Parameters

VoLTE RTP Packet


Loss

2015 Samsung

OR-JTST-0069
DT Route

2015 Samsung

Attach Result
Case#1 EMM Cause#15

2015 Samsung

TAC# of Cellref.

Succeed Case

Same TAC No. 8

TAC# for Failed Case

TAC# for Succeed Case

Failed Case
4

Attach Result
Case#1 EMM Cause#15 (MME Analysis)

2015 Samsung

#15 "No suitable cells in tracking area"


The MME receives the Diameter error DIAMETER_UNABLE_TO_DELIVER (3002) and no re-routing
takes place or DIAMETER_REALM_NOT_SERVED (3003) from another Diameter Agent (e.g. from a
Diameter EDGE Relay Agent or from the GRX/IPX)
5

Attach Result

2015 Samsung

No 200OK for Register

Attach Succeed

Case#2 No 200OK for REGISTER Message

Attach Result
OR-JTSG-ENB-9001 (PCI 27/28/29)

There are total 46 times of Attach Attempt in OR-JTSG-ENB-9001.


Among them, there are 2 times of Attach Failure in Sector2 during the 2 nd CLOT
drive testing as below,
- Case#1 : EMM Cause #15
- Case#2 : No 200OK for REGISTER from eNB

2015 Samsung

Appendix
Table A.2: Mapping between NAS Cause Code values and network
conditions

2015 Samsung

NAS cause code to UE


#2 "IMSI Unknown in HSS"

#14 "EPS services not allowed in this PLMN"

#19 "ESM failure"

#12 "Tracking area not allowed"

#25 "Not authorized for this CSG"

Condition
The MME receives a SGsAP-LOCATION-UPDATE-REJECT message
from the VLR indicating in the reject cause "IMSI unknown in HSS".
Only used in the Combined Tracking and Location Area Update procedure

The MME receives in Update-Location-Answer


message an indication of Roaming restricted in MME
due to unsupported feature
The value OPERATOR_DETERMINED_BARRING
is received in the Subscriber-Status AVP
The HSS indicates that due to subscription to a
"regionally restricted service" the UE is not allowed
to operate in the tracking area.
The CSG ID of the cell from where the UE has sent the TRACKING
AREA UPDATE REQUEST message is not contained in the Allowed CSG
list.

#15 "No suitable cells in tracking area"

The MME receives the Diameter error DIAMETER_UNABLE_TO_DELIVER


(3002) and no re-routing takes place or DIAMETER_REALM_NOT_SERVED
(3003) from another Diameter Agent (e.g. from a Diameter EDGE Relay Agent
or from the GRX/IPX)

#15 "No suitable cells in tracking area"

The MME detects that it cannot communicate with the HSS in the HPLMN of
the subscriber. How the MME detect this is implementation specific.

#14 "EPS services not allowed in this PLMN"


NOTE:

Any of those NAS Cause Code values may


be sent to the UE, depending on operator's
choice / configuration, e.g. NAS Cause Code
#14 is to be sent to the UE if the network is
an LTE only network.

Вам также может понравиться