Академический Документы
Профессиональный Документы
Культура Документы
Objectives
Page2
Purpose
RanShare enhancements:
Vendibility
Page3
Contents
1. RanShare Overview - BSS Sharing
2. Operator-Independent Power Resource Pool
3. Operator-Independent Abis Interface Transmission
Resources - TDM
4. Operator-Independent Abis Interface Transmission
Resources - IP
Page4
BSS Sharing: Dedicated TRX sharing, one cell is used by only one operator.
Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.
Page5
Multi-carrier Capability
Example 1:
Example 2:
8 Carriers for 2 operator 8 Carriers for 4 operator
8 Carriers @ 2*12.5 MHz @ 80W @CLASS II
GSM BSS
BSC
BTS
GSM
Carrier
5~8
GSM
Carrier
1~4
Huawei Confidential
Page 6
Huawei Confidential
Page7
Feature Enhancements
Page8
Contents
1. RanShare Overview - BSS Sharing
2. Operator-independent power resource pool
3. Operator-Independent Abis Interface Transmission
Resources - TDM
4. Operator-Independent Abis Interface Transmission
Resources - IP
Page9
Application Scenarios
Each MRRU module serves the cells of multiple operators at the same
time.
Suburban areas with low user density
Page10
Networking requirements
Hardware requirements
N/A
MRRU V2&V3
Software requirements
Page11
Function Description
Page12
Function Description
Page13
Impacts on Performance
Network Performance
Indicator
Impact
Reason
Congestion rate
Page14
Page15
Page16
Page17
Step 1: Configure BSS Sharing and set the correlations between cells
and operators (omitted).
Step 2: Set the power pool for each operator on the RXU Board
Parameters tab.
Step 3: Set the power table on the Site TRX Dev Property tab.
Page19
Step 2: Set the power pool for each operator on the RXU Board Parameters tab.
The procedure for navigating to the RXU Board Property dialog box is as follows: On the
Main View tab, right-click a BTS, and choose Device Panel from the shortcut menu. In the
RXU topology, right-click an RXU, and choose RXU Board Parameters from the shortcut
menu. The RXU Board Parameters dialog box is displayed.
The total transmit power of all operators is smaller than or equal to the transmit
capability of the channels.
Page20
Step 3: Set the power table on the Site TRX Dev Property tab.
The procedure for navigating to the Site TRX Dev Property tab is as follows: On
the Main View tab, right-click a TRX, and choose TRX Configuration Express
from the shortcut menu. On the Properties tab, select Site TRX Dev Property.
The Site TRX Dev Property table is displayed.
Page21
Contents
1. RanShare Overview - BSS Sharing
2. Operator-independent power resource pool
3. Operator-Independent Abis Interface Transmission
Resources - TDM
4. Operator-Independent Abis Interface Transmission
Resources - IP
Page18
Application Scenarios
Page19
Networking requirements
Chain topology, ring topology, bypass, FlexAbis, and 16K are not supported.
High-Level Data Link Control (HDLC), DXX, and TGW Flex networking are not
supported.
Hardware requirements
N/A
Software requirements
Page20
Function Description
Shared or
Dedicated
Physical Link
Operator-A
Physical Link
Operator-B
Page21
Step 1: Configure the BSS sharing function so that cells correspond to homing
operators. (Omitted)
Step 2: Run SET BTSSHARING to configure the transmission separation
function.
Operator Name
Step 4: Run SET BTSIDLETS to set the number of idle timeslots of the
operator (perform this step when the BTS is deactivated).
Operator Name
Idle TS Count
Page22
Page23
Page24
Page25
Step 1: Configure BSS Sharing, and set the correlations between cells and operators
(omitted).
Step 2: Disable transmission sharing in the BTS RanSharing Parameters table.
Step 3: Set the operator for E1 port. This operation must be performed when the BTS is
inactive.
Operator
Step 4: Set the quantity of idle slots for an operator. This operation must be performed
when the BTS is inactive.
Operator Name
Page30
Page31
Step 3: Set the operator for E1 port. This operation must be performed when
The procedure for navigating to the Add Chain dialog box is as follows: On the
Main View tab, right-click an MBSC, and choose Show BTS Topology from the
shortcut menu. In the BTS topology, right-click a BTS, and choose Chain
Management from the shortcut menu. The Chain Management dialog box is
displayed.
Page32
Step 4: Set the quantity of idle slots for an operator. This operation must be
performed when the BTS is inactive.
The procedure for navigating to the Timeslot Chart dialog box is as follows: On
the Main View tab, right-click an MBSC, and choose Show BTS Topology from
the shortcut menu. In the BTS topology, right-click a BTS, and choose Timeslot
Management from the shortcut menu. The Timeslot Chart dialog box is displayed.
Page33
Contents
1. RanShare Overview - BSS Sharing
2. Operator-independent power resource pool
3. Operator-Independent Abis Interface Transmission
Resources - TDM
4. Operator-Independent Abis Interface Transmission
Resources - IP
Page26
Application Scenarios
The sharing policies for the entire logical port tree (including
physical ports) are the same.
Page27
Networking requirements
Abis IP transmission
It is not recommended in the case of Abis/IuB logical port sharing or PPP/MP link
sharing.
Hardware requirements
N/A
Software requirements
Page28
Function Description
Shared
Shared or
Dedicated
Page29
Step 1: Configure the BSS sharing function so that cells correspond to homing
operators. (Omitted)
Step 2: Run SET BTSSHARING to configure the transmission separation
function (see page 23).
Step 3: Run ADD OPSEPINFO to set the admission bandwidth ratio and load
threshold of the operators in operator admission separation mode.
Step 4: Run ADD IPLOGICPORT to set the admission separation mode used
by the logical port (perform this step when the BTS is deactivated).
Page30
Page31
Page32
Step 1: Configure BSS Sharing, and set the correlations between cells and
operators (omitted).
Step 2: Separate transmission (same as that in the preceding section).
Step 3: Set the bandwidth ratio and load threshold of each operator separately.
Step 4: Set the access separation mode for a port. This operation must be
performed when the BTS is inactive.
Page41
Step 3: Set the bandwidth ratio and load threshold of each operator separately.
The procedure for navigating to the Separate Information for Operators table is
as follows: On the Main View tab, right-click an MBSC, and choose GSM Global
Configuration Express from the shortcut menu. On the Properties tab, click
Separate Information for Operators. The Separate Information for Operators
table is displayed in the right pane.
Page42
Step 4: Set the access separation mode for a port. This operation must be
performed when the BTS is inactive.
The procedure for navigating to the IP Logical Port table is as follows: On the
Transmission View tab, right-click Abis, and choose Abis Configuration
Express from the shortcut menu. On the Properties tab, click IP Logical Port.
The IP Logical Port table is displayed in the right pane.
Page43
Thank you
www.huawei.com