Академический Документы
Профессиональный Документы
Культура Документы
Principles
Relative Density principles apply to
compaction of relatively clean, coarse-
grained soils.
Relatively clean usually taken to be less 12
% or less finer than the #200 sieve.
Important for compaction study of filters
Objectives
w%
Compacting Clean Sands
filling a steel
mold. ASTM
Method D4254
Minimum Index Density
After filling the
mold, excess soil
is carefully screed
off. The volume
of this mold is 0.1
ft3. Knowing the
weight of soil in
the mold, the dry
density is easily
computed
Maximum Index Density
Example Minimum dry density = 96 pcf
Maximum index density of clean sand
results from vibration at high amplitude on
vibratory table for 10 minutes.
ASTM D4253
Example Maximum dry density = 117.5 pcf
Maximum Index Density
Weight on
sample inside
sleeve
Vibratory
table
Maximum Index Density
Weight on
sample inside
sleeve
Vibratory
table
Maximum Index Density
Sample
densified by
vibration
Measure D
height to
determine
new gd
Plate on which weight
sits during vibration
Void Ratio and Dry Density
The void Ratio is calculated for each state of
denseness of sample.
Maximum void ratio occurs at minimum index
density - For Example Min.gd = 96.0 pcf
Minimum void ratio occurs at maximum index
density For Example Maximum gd = 110.0 pcf
Gs g water
e 1
g dry
Minimum and Maximum Void Ratios
emax emeasured
Rd (%) x100
emax emin
Diagram below illustrates a
relative density of about 40 %
emeasured
emin emax
emax emeasured
Rd (%) x100
emax emin
0.7225 0.6133
Rd (%) x100 49.9%
0.7223 0.5033
Compute Relative Density
Relative Density Equation
(rewritten in dry density terms)
Solve for Example:
g d max g d g d min
Rd (%) 100
g d g d max g d min
110.0102.5 96.0
Rd (%) 100 49.8%
102.5110.0 96.0
Fort Worth Relative Density Study
NRCS lab in Fort Worth studied 28 filter
sands and used some published data
Minimum and Maximum Index Densities
were performed on each sample
A 1 point dry Standard Proctor energy mold
was also prepared for each sample.
Values of 50% and 70% relative density were
plotted against the 1 point Proctor value
70 % Relative Density vs. 1 Point Proctor
130
125
120
70 % Relative Density
115
110
100
90
90 95 100 105 110 115 120 125 130
Field 1 Point Proctor Test Dry Density, pcf
70 % Relative Density vs. 1 Point Proctor
120
best fit line
115
110
50 % Rd
105
100
95 95 % of 1
point
90
90 95 100 105 110 115 120 125 130
Field 1 pointdry density
50 % Relative Density vs. 1 Point Proctor
Given:
Minimum index density is 96.5 pcf
Maximum index density is 111.5 pcf.
Gs g water 2.65 62.4
emax 1 1 0.7136
g min_dry 96.5
0.7136 emeasured
70 x100
0.7136 0.4831
Class Problem Solution
Solving and Rearranging the equation:
0.7136 emeasured
70 x100
0.7136 0.4831
70 0.7136 emeasured
100 .2305
0.16135 0.7136 emeasured
emeasured 0.7136 0.16135 0.5225
Class Problem Solution
Now, calculate a value for dry density at this void
ratio:
Gs g water 2.65 62.4
e 1 0.55225 1
g dry g dry
Gravelly sand
120
Dry Density, pcf
100
90
Reference - Donovan, N.C. and Sukhmander Singh, "Liquefaction Criteria
for the Trans-Alaska Pipeline." Liquefaction Problems in Geotechnical
Engineering, ASCE Specialty Session, Philadelphia, PA, 1976.
80
0 10 20 30 40 50 60 70 80 90 100
Relative Density, %
Other information on Relative Density
45
35
30
Average
25
20
15
Reference ભ Donovan, N.C. and Sukhmander Singh,
"Liquefaction Criteria for the Trans-Alaska Pipeline." Liquefaction
10
Problems in Geotechnical Engineering, ASCE Specialty Session,
Philadelphia, PA, 1976.
5
0 10 20 30 40 50 60 70 80 90 100
Relative Density, %
Class Problem