Академический Документы
Профессиональный Документы
Культура Документы
M6000-3S Overview
M6000-3S Board Introduction
M6000-3S Power Heat Dissipation System
Internal use only▲
Overview
ZXR10 M6000-S is a carrier-class router. It is used for M6000-18S
MAN of operators, WLAN, IDC and backbone
convergence network of the Government & Enterprise
Network, providing 200G/400G solution scheme, and M6000-8S Plus
granted with 1T evolution capability so as to meet the
demand of service bearing and network evolution for
Government & Enterprise Network clients. M6000-8S
M6000-5S
M6000-3S
Height: 4U (DC)/ 5U (AC) Height: 7U (DC)/ 8U Height: 14U (DC) Height: 22U (DC/AC) Height: 41U (DC/AC)
Number of service slots: 3 (AC) Number of service Number of service Number of service
Switch system: Full mesh Number of service slots: 8 slots: 8 slots: 18
Power supply: AC/DC, 1+1 slots: 5 Switch system: 3+1 Switch system: 3+1 Switch system: 6+2
Switch system: 1+1 Power supply: DC, 2+2 Power supply: AC/DC, Power supply: AC/DC
Power supply: AC/DC, 4+4/5+1 8+8/11+1
1+1
Internal use only▲
Networking Location
DHCP/ BSS/
NMS AAA
BRAS DNS OSS
OAM
HG SW/ONU OLT/Agg SW ISPA ISPB
SR/MSE
SW/OLT CR
VAS IP
FTTB/C Public Plane Internet
MGCF/IM-MGW
Traffic Analysis System
P IGW IMS
PE
VIP
IP RAN/Metro IPTV
PE
BS MPLS IDC
Telecom Plane
AG
PDSN/GGSN
Internal use only▲
ZXR10 M6000-3S
Power AC
DC
module HVDC
Single-
Port capacity 600Gbps
module
2650W 2675W
output
Slot throughout
power 200G
Power
capacity
redundan 1+1 1+1
cy
Service slot 3
Variable rate fan
Fan shelf x 3 175 ×442 ×738
2 dual-fans/module
Outline 4RU (DC shelf)
dimension
Service line card
mm H×W×D 219.4 ×442 ×738
PFU x 3
5RU (AC shelf)
Parameters
Standard IEC60297-2
220mm*600mm*800mm(
Dimension height*width*depth)
Capacity 47U
Height 124kg
Capability 19-inch standard device
•Noise isolation
•Anti dust
•Anti mouse
Contents
M6000-3S Overview
M6000-3S Board Introduction
M6000-3S Power Heat Dissipation System
内部公开▲ Internal use only▲
7
M6KS-MPU-A Main Control Board 内部公开▲ Internal use only▲
8
M6KS-MPU-A Main Control Board 内部公开▲ Internal use only▲
ALM Red It is the system alarm indicator. When a fault occurs, it lights up. It dims
out when the system is in normal state.
ACT Green System active indicator. It is on when the board is active and off when
the board is standby.
LINK Green The link indicator for the first gigabit electrical interface. It is turned on
when the link is normal. .
9
内部公开▲ Internal use only▲
FUN Function button. It is used to collect the system operation state and configuration. Press this button for more than 6
seconds.
RST It is used to reset the whole board.
EXCH/OFL Active/standby changeover button. It is used to change over between the active board and the standby board
manually. When the board is a standby board, this button is a hot swapping button.
10
内部公开▲
Internal use only▲
11
内部公开▲
Internal use only▲
12
内部公开▲
Internal use only▲
13
内部公开▲
Internal use only▲
STATUS indicator
Power-on initialization On for 0.5 s On for 0.5 s The indicator can be used normally.
It is lit green at first and then turns to red
14
内部公开▲
Internal use only▲
OFL indicator
State Description
15
内部公开▲
Internal use only▲
16
内部公开▲
Internal use only▲
STATUS indicator
Power-on initialization On for 0.5 s On for 0.5 s The indicator can be used normally.
It is lit green at first and then turns to red
18
内部公开▲
Internal use only▲
OFL indicator
State Description
19
Contents
M6000-3S Overview
M6000-3S Board Introduction
M6000-3S Power Heat Dissipation System
Internal use only▲
M6000-3S AC Power
1 Switch
2 Handle
4 Setscrew