Академический Документы
Профессиональный Документы
Культура Документы
WCDMA BTS3900
Hardware Structure
BTS3900V200R010 www.huawei.com
boards of BTS3900
Iu-CS
RNC
Iub
Iu-BC
CS
NodeB
Iu-PS
Iur
NodeB PS
Iu-BC
Iub
NodeB
RNC
CBC
RNC
Iub
BTS3900 cabinet
Transmission
power supply DDF device
system
Environment
Monitoring
device
O&M terminal
BTS3900 System
1U
9U
19U
2U
1U
1U
2U
1U
2U
3U
BTS3900 can support up to: uplink 1536 CEs and downlink 1536 CEs
BTS3900 can support up to: 3*8 cells or 6*4 cells
Characteristics
PSU Power
Module
DCDU
WRFU
Iub BBU
RNC
Baseband Transmission WRFU
Control module RF Module Antenna
Signal Current
Control Subsystem
Signaling Operation& Power mode
Clock mode Processing Maintenance
Decoding Demodulation
FP Processing
E1/T1 Transmission
FE Adaptation Power Interface
Transport Protocol CPRI
Control TO WRFU
RNC Interface Processing information Module
Codling Modulation
Full configuration
Typical configuration
LEDs
Commissioning:RJ45 IP transmission
Optical signals: SFP 4E1:DB26
0.125s ON, 0.125s OFF The software is being loaded to the board, or the
board is not in use.
ALM Red ON The board is reporting hardware alarms.
Settings of SW2
Bit 120-ohm E1 75-ohm E1
Balanced Mode Unbalance Description
d Mode
1 OFF ON The RRING is for
connected to the
2 OFF ON
protection ground
3 OFF ON
4 OFF ON
RUN Green ON The board has power input, yet the board is faulty.
ON The board has alarms on hardware and it should be replaced with a new one.
OFF normal
CPRI0 Red
CPRI1 Green ON The CPRI links over the optical cable are faulty.
CPRI2 Blinking at 2 Hz The RRU on the CPRI link is faulty in hardware.
Blinking at 0.5 Hz The RRU on the CPRI link is faulty in the antenna system connection.
Main Functions:
Main Functions:
LED: The UPEU has one LED, indicating the running status of the board.
Socket and Port: The UPEU has one socket and four ports.
UTRP board should add sub board to provide the different interface type.
WD22UTRP is the main board name. The UTRP has three sub-boards in current version
− UAEU: Eight ATM over E1s/T1s
− UIEU: Eight IP over E1s/T1s
− UUAS: One unchannelized ATM over SDH/SONET(STM-1/OC-3) interface
The board in
Transmission gray
Sub table is not
board be delivered
Interface type currently. Interface specification
Board name name
DB25 DB26
E1 Connection:
E1
E1
Indoor DDF
DIP Switch: The UELP has one DIP switch, which is used to select whether the
IP Cable Connection.
Transmission Equipment
LAN switch or Router
On for 0.125 second and off for 0.125 The module is loading software or is not started.
second
ALM On The module is in the alarm status.
On for 1 second and off for 1 second The module is in the local test status.
Red LED on for 1 second and off for The CPRI link is out of lock.
1 second
The maximum access search radius is configurable with the step size of 300 m
Configuration Type (No Transmit Diversity Typical Power Maximum Power
Transmit Diversity) Power (W)/Carrier Consumption (W) Consumption (W)
220 V AC Distribution
Function
- 48V DC
Single Cabinet
Power output port SPARE2, SPARE1, RFU0 to RFU5 supplying power to six WRFUs
BBU, FAN, and RFU5- BBU supplying power to the BBU
RFU0 FAN supplying power to the FAN
SPARE1 and SPARE2 reserved
Power switch SPARE2, SPARE1, RFU0 to RFU5 controlling the ON/OFF of the current of
BBU, FAN, and RFU5- six WRFUs
RFU0 BBU controlling the ON/OFF of the current of the BBU
FAN controlling the ON/OFF of the current of the FAN
SPARE1 and SPARE2 controlling the ON/OF of the
current on the SPARE1 and SPARE2 power output ports
Alarm output port SPD ALM DUDU-01 dry contact alarm output port
Fault LED Red Off Normal, or the PSU has no output because of faults (such as no AC
input, or overvoltage and undervoltage of AC input) on the mains.
The power and environment monitoring unit (PMU) is the unit for monitoring the
power and the environment. The PMU provides perfect power system management,
power distribution detection, and alarm report functions.
RUN Green On for 1 second and The module is functional, and the communication with the
off for 1 second main control unit is normal.
On for 0.125 second The module runs normally but the communication with the
and off for 0.125 main control unit fails.
second If the PMU does not communicate with the main control unit
for one minute, the communication fails. In this situation, the
RUN LED blinks four times every second.
Battery control The battery control switch has two control ports ON and OFF, which are
switch used for powering on and off the battery.
Press and hold the port ON for 5s to 10s until the battery is powered on.
Press and hold the port OFF for 5s to 10s until the battery is powered off.
CAUTION:
You need to insert a small round bar into the hole when you operate the
battery control switch. When you hear a crack, the battery is powered on or
off.
To operate the battery control switch on the front panel of the PMU, insert
a small round pole into the hole.
Power supply test Two power supply test holes -48 V and 0 V are available for measuring
port power voltages through an ordinary multimeter.
The FAN unit refers to the fan box. The FAN unit provides the functions of ventilation
and heat dissipation for cabinets. One FAN unit has four independent fans.
OT terminal
E1 Cable FE Cable
This part illustrates the configuration type of the BTS3900 by taking the WBBPa
supporting three cells and the WRFU supporting the 80W/4 carrier as an example.