Академический Документы
Профессиональный Документы
Культура Документы
www.huawei.com
• RTN310
Scenario: New sites which is not 7G or SD configuration
Frequency ranges on 13G/15G/23G/38G in STC projects.
Normally it is 2+0 configuration . (XPIC)
• RTN380
Scenario: New sites with short distance link(normally less than 1.3km)
Frequency is 80G, providing big bandwidth range from 500M to 2G.
Normally it is 1+0 configuration.
• ATN905/ATN910I
Used as switch to aggregate all the technologies.
ATN905 at terminal site, ATN910I at the Hub site.
Page 3
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential
RTN950A Introduction
2U high
Slot 7 is for CSHO card.
2 power connecter is located on the
CSHO card which is 1+1 protection
Suggest 12~16A breaker
Total slot1~slot6 for IF cards and traffic
cards
• CSHO card:
Power Connector GE1~GE4(RJ45) GE5&GE6(SFP) 2*STM-1
16*E1 interface
Page 4
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential
RTN310 Introduction (V1R1) (1/2)
Page 7
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 7
RTN380 Introduction (V1R2) (2/2)
Connecto Connector
Color Signal
r X1 X2
X1.1 X2.1 White/Orange RX+
X1.2 X2.2 Orange RX-
X1.3 X2.3 White/Green TX+
X1.4 X2.4 Blue RSSI Ground
X1.5 X2.5 White/Blue Reserved
X1.6 X2.6 Green TX-
RSSI Test Level
X1.7 X2.7 White/Brown
Signal
X1.8 X2.8 Brown Reserved
Interface
Port Name Function
Type
ETH/OAM RJ-45 NM interface or console interface
CLK RJ-45 Clock input/output interface
TOD RJ-45 Time input/output interface
ALMI/O RJ-45 Alarm input/output interface
GE0 to GE3 SFP GE service interface
FE/GE0 to FE/GE3 SFP FE/GE service interface
FE/GE4 to FE/GE7 RJ-45 FE/GE service interface
Page 9
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 9
ATN905 Introduction
Power cable
RTN310 RTN310 Optical Cable
RJ45 LAN Cable
PoE Cable/Outdoor LAN Cable
FE/GE7
4G FDD BBU
ATN910
GE0 GE1
Page 11
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential
Hardware Design and Port Assignment (2/5)
Scenario 2: ATN905 with RTN310, 2+0 (XPIC) Configuration
RTN310 RTN310
Power cable
Optical Cable
RJ45 LAN Cable
PoE Cable/Outdoor LAN Cable
FE/GE0 2G BBU
Page 12
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential
Hardware Design and Port Assignment (3/5)
Scenario 3: ATN910 with RTN380, 1+0 Configuration
Power cable
Optical Cable
RJ45 LAN Cable
RTN380 PoE Cable/Outdoor LAN Cable
Outdoor
LAN Cable
FE/GE4 2G BBU
RTN380
GE Optical To
To PI FE/GE5 3G BBU
Port ATN GE(O)
FE/GE7
4G FDD BBU
ATN910
PI
P&E Port
GE0
Power cable
RTN380 Optical Cable
Outdoor
LAN Cable RJ45 LAN Cable
PoE Cable/Outdoor LAN Cable
RTN380
GE Optical To
Port To PI FE/GE1
ATN GE(O) 3G BBU
Fiber Cable
DCDB FE/GE3
4G FDD BBU
ATN905
FE/GE4
PI
P&E Port
FE/GE2 4G TDD BBU
FE/GE0 2G BBU
Power cable
RTN380 Optical Cable
Outdoor
LAN Cable RJ45 LAN Cable
PoE Cable/Outdoor LAN Cable
To 3G small cell
DOCK
AC input
4G small cell
DOCK
WAN Port
CWO
ready VLAN/IP
Preparation on site
Check the material, whether it is complete and there is no damage
during the transportation
Installation availability:
Tower space available or not?
Rack space available or not?
Breaker available or not?
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 16
Question:
1. The designed antenna height is occupied, there is available space at higher
location , can I install the antenna on this location?
2. I tried to do alignment , but I still can’t get the RSL, what should I do? Can I
increase the antenna height?
2. Allow vlan 4094 on the ATN ports of both that connected with RTN and the one
going to connect with laptop.
Port connect with Laptop should be access mode or the Laptop should be vlan
supported.
4. Make ping test on the RTN IP. Ping result should be OK, then we can login via
WEBLCT.