Академический Документы
Профессиональный Документы
Культура Документы
Model 38119
Set up and Operating Instructions
herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Dia-
grams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may
differ slightly from the product described herein. Tools required for assembly and service may not be included.
21. NEVER LEAVE TOOL RUNNING 10. People with pacemakers should
UNATTENDED. TURN POWER OFF. consult their physician(s) before
Don’t leave tool until it comes to a use. Electromagnetic fields in close
complete stop. proximity to heart pacemaker could
cause pacemaker interference or
pacemaker failure. In addition,
Drill Press Safety Warnings
people with pacemakers should:
For Your Own Safety Read Instruction • Avoid operating alone.
Manual Before Operating Drill Press • Do not use with power switch locked
on.
1. Wear eye protection. • Properly maintain and inspect to
2. Do not wear gloves, necktie, or loose avoid electrical shock.
clothing. • Any power cord must be properly
grounded. Ground Fault Circuit
3. Clamp workpiece or brace against Interrupter (GFCI) should also be
column to prevent rotation. implemented – it prevents sustained
electrical shock.
4. Use recommended speed for drill
accessory and workpiece material. 11. Some dust created by power
sanding, sawing, grinding, drilling,
5. The use of accessories or and other construction activities,
attachments not recommended by contains chemicals known [to the
the manufacturer may result in a risk State of California] to cause cancer,
of injury to persons. birth defects or other reproductive
6. When servicing use only identical harm. Some examples of these
replacement parts. chemicals are:
• Lead from lead-based paints
7. Only use safety equipment that has • Crystalline silica from bricks and
been approved by an appropriate
SKU 38119 For technical questions, please call 1-800-444-3353. Page 5
cement or other masonry products first be examined by a doctor and
• Arsenic and chromium from then have regular medical check-
chemically treated lumber ups to ensure medical problems are
Your risk from these exposures not being caused or worsened from
varies, depending on how often you use. Pregnant women or people
do this type of work. To reduce your who have impaired blood circulation
exposure to these chemicals: work in to the hand, past hand injuries,
a well ventilated area, and work with nervous system disorders, diabetes,
approved safety equipment, such as or Raynaud’s Disease should not
those dust masks that are specially use this tool. If you feel any medical
designed to filter out microscopic or physical symptoms related to
particles. (California Health & Safety vibration (such as tingling, numbness,
Code § 25249.5, et seq.) and white or blue fingers), seek
medical advice as soon as possible.
12. WARNING: Handling the cord on
this product will expose you to lead, 2. Do not smoke during use. Nicotine
a chemical known to the State of reduces the blood supply to the
California to cause cancer, and hands and fingers, increasing the risk
birth defects or other reproductive of vibration-related injury.
harm. Wash hands after handling.
(California Health & Safety Code § 3. Wear suitable gloves to reduce the
25249.5, et seq.) vibration effects on the user.
13. The warnings, precautions, 4. Use tools with the lowest vibration
and instructions discussed in when there is a choice between
this instruction manual cannot different processes.
cover all possible conditions and 5. Include vibration-free periods each
situations that may occur. It must day of work.
be understood by the operator that
common sense and caution are 6. Grip tool as lightly as possible (while
factors which cannot be built into this still keeping safe control of it). Let
product, but must be supplied by the the tool do the work.
operator.
7. To reduce vibration, maintain the tool
as explained in this manual. If any
Vibration Safety
abnormal vibration occurs, stop use
This tool vibrates during use. immediately.
Repeated or long-term exposure to
vibration may cause temporary or Save these
permanent physical injury, particularly
to the hands, arms and shoulders. To instructions.
reduce the risk of vibration-related
injury:
1. Anyone using vibrating tools regularly
or for an extended period should
4 MM
5 MM I.D. x 11 MM O.D.
Flat Washer
Figure 1
REV 01b
Specifications
Electrical Requirements 120 V~ / 60 Hz Maximum Distance from
10”
620, 1100, 1720, Chuck to Base
Spindle Speeds
2340, 3100 RPM Maximum Swing 8”
Drill Chuck Capacity 1/2” Column Diameter 1.89”
Maximum Spindle Stroke 2” Table Size 6-5/16” x 6-1/2”
Maximum Distance from Overall Dimensions 23” x 7” x 17”
6-3/4”
Chuck to Table Base Size 7” x 11-1/8”
E105017
Table to Column
1. Thread the Table Support Locking Handle (6) into the Figure 2
Table Support (4) from the left hand side, and leave it
loose until later.
2. Slide the Table Support with Table over the Column
(11) and secure at a convenient position by tightening
the Table Support Locking Handle.
Head to Column
1. It may be necessary to unscrew the Head Lock Set
Screws (3) slightly to ensure they do not protrude
internally, as this will prevent the head from sliding fully
into position.
2. With assistance, raise the Head and place it on top of
the Column, ensuring it slides home fully.
3. Align the head with the base (7), and firmly secure with
the Head Lock Set Screws (3).
4. Screw the three Feed Handles (15) firmly into the hub of the Feed Shaft.
Figure 5
Operation
1. Secure the tool to a supporting structure before use.
2. Insert the drill into the jaws of the chuck approximately 1”, ensuring that the jaws
do not touch the flutes of the drill. Before tightening the chuck, ensure that the drill
is centered within the jaws. Refer to Figure 6.
3. Make sure the table height and position is set
so that the drill travel range is sufficient for the
material to be drilled.
4. Make sure the work is securely clamped. That Figure 6
is, held in a drill vice, or bolted to the table. Never
hold the material with your bare hands while
drilling. Severe personal injury may be caused if
the material is flung out of the operator’s hand.
5. IF THE MATERIAL IS IRREGULARLY SHAPED and cannot be laid flat on the
table, it should be securely blocked and clamped. Any tilting, twisting or shifting
will result not only in a roughly drilled hole but also increases the chances of
damage to the drill.
Cutting Speeds
Factors which determine the best speed to use in the drill press operation are:
a. Type of material to be drilled
b. Size of hole
c. Type of drill bit
d. Quality of the hole/cut desired.
Generally, the SMALLER THE DRILL BIT the GREATER THE OPTIMAL RPM. In soft
material, the speed should be higher than for hard metals. As a guide, the drill speed for
a given drill bit size is listed in the chart below.
SPEED RANGE (RPM) 3100 2340 1720 1100 620
Wood in 3/8 5/8 7/8 1-1/4 1-5/8
mm 9.5 18 22 31.75 41.4
Zinc Diecast in 1/4 3/8 1/2 3/4 7/8
mm 6.4 9.5 12.5 19 25.4
Aluminum & Brass in 7/32 11/32 15/32 11/16 3/4
mm 5.6 8.75 12 17.5 19
Mild Steel & Iron in 3/32 5/32 1/4 3/8 1/2
mm 2.4 4 6.4 9.5 12.5
After Operation
1. Remove debris and drill bits from the machine. Thoroughly clean and dry all
surfaces. Oil machined surfaces lightly.
2. Child-proof the machine and work area. Use padlocks, master switches and/or
remove starter keys.
Troubleshooting
REV 01d
11
10
8
Part Numbers shown
here have “C” suffix
Part Numbers shown
here have “B” suffix
9
REV 01b